Ankr-TITE® Wedge Anchor- Hot-Dip Galvanized Steel with 304 SS Clip Mechanical Anchors Wej-It

Roll over image to zoom in

Ankr-TITE® Wedge Anchor — Hot-Dip Galvanized Steel with 304 SS Clip

This pre-assembled high strength, fully threaded, and torque-controlled expansion wedge anchor has a unique safety shoulder in the expansion cone that supports a thick 3-dimple clip engineered to provide high load carrying capability and reduce slip in a variety of installation conditions. Nut and washer included.

Pack Price

$37.80

Quantity

ENGINEERED IN THE USA

Materials / Finishes

Available in:
Hot-Dip Galvanized Steel
304 Stainless Steel
316 Stainless Steel
Zinc Plated Carbon Steel

Features and Benefits

Length and identification code stamped on head to ease identification pre and post-installation
Dog-point head prevents point damage during installation
Fully threaded anchor body accommodates various application thickness
Enlarged 3-dimple clip
- Increases response in lightweight concrete and requires fewer rotations to achieve desired torque
- 360 º segment contact on clip equalizes load distribution and increases load-carrying capacity
Unique safety shoulder
- Supports the 3-dimple clip under maximum and ultimate loads, preventing slippage
- Similar products have gradual expansion cone that does NOT have a safety shoulder to support the clip when anchor is under strain

Downloads

Technical Flyer

Product Details

Installation

Catalog Number

Anchor Size

Min. Embed.

Thread Length

Box Quantity

Carton Quantity

ATG1413

1/4 x 1-3/4

1-1/4

3/4

100

800

ATG1421

1/4 x 2-1/4

1-1/4

100

800

ATG1431

1/4 x 3-1/4

1-1/4

2-1/4

100

800

ATG3821

3/8 x 2-1/4

1-3/4

1

50

400

ATG3823

3/8 x 2-3/4

1-3/4

1-1/2

50

400

ATG3830

3/8 x 3

1-3/4

50

400

ATG3833

3/8 x 3-3/4

1-3/4

2-1/2

50

400

ATG3850

3/8 x 5

1-3/4

3-1/4

50

400

ATG3870

3/8 x 7

1-3/4

4-1/2

50

300

ATG1223

1/2 x 2-3/4

2-1/8

1-1/8

25

200

ATG1233

1/2 x 3-3/4

2-1/8

25

200

ATG1241

1/2 x 4-1/4

2-1/8

2-5/8

25

200

ATG1242

1/2 x 4-1/2

2-1/8

2-5/8

25

200

ATG1252

1/2 x 5-1/2

2-1/8

3-3/4

25

150

ATG1270

1/2 x 7

2-1/8

4-1/2

25

150

ATG1282

1/2 x 8-1/2

2-1/8

5

10

40

ATG1210

1/2 x 10

2-1/8

5

10

40

ATG1212

1/2 X 12

2-1/8

5

10

40

ATG5832

5/8 x 3-1/2

2-5/8

1-1/2

10

80

ATG5841

5/8 x 4-1/4

2-5/8

2-3/8

10

80

ATG5842

5/8 x 4-1/2

2-5/8

10

80

ATG5850

5/8 x 5

2-5/8

3-1/8

10

80

ATG5860

5/8 x 6

2-5/8

4

10

80

ATG5870

5/8 x 7

2-5/8

4-1/2

10

80

ATG5882

5/8 x 8-1/2

2-5/8

5

10

40

ATG5810

5/8 x 10

2-5/8

5

10

40

ATG5812

5/8 x 12

2-5/8

5

10

40

ATG3441

3/4 x 4-1/4

3-1/4

2

10

80

ATG3443

3/4 x 4-3/4

3-1/4

2-1/2

10

80

ATG3452

3/4 x 5-1/2

3-1/4

10

60

ATG3461

3/4 x 6-1/4

3-1/4

3-3/4

10

60

ATG3470

3/4 x 7

3-1/4

4-3/4

10

60

ATG3482

3/4 x 8-1/2

3-1/4

5

10

40

ATG3410

3/4 x 10

3-1/4

5

10

40

ATG3412

3/4 x 12

3-1/4

5

4

16

ATG7860

7/8 x 6

3-7/8

3-1/2

4

24

ATG7880

7/8 x 8

3-7/8

5

4

16

ATG7810

7/8 x 10

3-7/8

5

4

16

ATG1060

1 x 6

4

3

4

24

ATG1090

1 x 9

4

5

4

16

ATG1012

1 x 12

4

5

4

16

ATG11490

1-1/4 x 9

5-5/8

5

4

12

ATG11412

1-1/4 x 12

5-5/8

5

4

12

Drill the hole, whose diameter equals the anchor diameter, perpendicular to the work surface. To assure full holding power, do not ream the hole or allow the drill to wobble.
Drill the hole deeper than the intended embedment, but not closer than two diameters to the opposite surface of the concrete.

A clean hole is necessary for proper performance. Clean the hole using a nylon brush and compressed air.
Assemble the nut and washer onto the anchor. Drive the anchor through the material to be fastened at the calculated embedment depth.
Tighten the nut, or head, 3 to 5 turns past the hand tight position. Installing with a torque wrench is recommended for optimum performance. Refer to Recommended Setting Torque* in the table below.

NOTE: Always wear safety glasses. Follow drill manufacturer's instructions. Use only solid carbide- tipped drill bits meeting ANSI B212.15 diameter standards.